Motion Control System SIMOTION

HMI via ethernet connection

Erstellt von Mothilal am 30.11.2011 08:39 (5 Antworten)

  30.11.2011, 08:39

Mothilal Beigetreten am: 30.11.2011 Letzter Besuch: 12.03.2013 Beiträge: 164 Bewertung:  (21)

(0)  Dear expert and all               I am facing the problem in HMI via ethernet connection. I have my laptop(PG/PC) , SIMOTION C 240, and HMI (MP 277 10" TOUCH)winCC flexible 2008. I have attached my hardware configuration in the form of screen chart.I could go online with my simotion controller from my pc through ethernet. but i cant in HMI. Is it possible to acess the HMI from PC? PG/PC--- SIMOTION= ethernet SIMOTION--- HMI = profibus (12Mbps) Can i download or access HMI from my PC? Please help me (note: we could access the HMI and SIMOTION via profibus (by CP5512) and the node address are detected. we are trying to access the hmi via ethernet ) Thanks Dateianhang: hardware_config.zip  (22 Downloads) === Edited by O_Moderator @ 11/30/2011 10:52 AM [GMT ] === new subject after splitting from Profibus FMS to Ethernet ***ALL IS WELL***

Top

  30.11.2011, 17:32

Tweety Beigetreten am: 05.09.2011 Letzter Besuch: 22.05.2013 Beiträge: 2576 Bewertung:  (131)	(0)  Hello, Perhaps, this FAQ can help you? How do you use WinCC flexible to transfer a project to an operator panel via S7 routing? Tweety
	Top

  01.12.2011, 08:05

Mothilal Beigetreten am: 30.11.2011 Letzter Besuch: 12.03.2013 Beiträge: 164 Bewertung:  (21)	(0)  Dear sir,            Thanks for your reply. We are using the following cpu configuration. routing is possible for this CPU model? because i couldnot find this cpu model in your posted page. SIMOTION C240 : V4.1 ---6AU1240-1AA00-0AA0 SIMATIC MANAGER: V5.5+HF4 WinCC flexible 2008 SP2 pls clarify thanks ***ALL IS WELL***
	Top

  01.12.2011, 08:36

ChristophD Beigetreten am: 12.05.2006 Letzter Besuch: 22.05.2013 Beiträge: 1549 Bewertung:  (115)	(1)  Hello, yes routing is avaiable for SIMOTION C240. You must assign a PG/PC on then ehternet Network and select the NIC which communicate with the C240. take a look on this thread https://www.automation.siemens.com/WW/forum/guests/PostShow.aspx?PageIndex=1&PostID=320254&Language=en&onlyInternet=False#top Regards Christoph
	Top

  02.12.2011, 09:52

Mothilal Beigetreten am: 30.11.2011 Letzter Besuch: 12.03.2013 Beiträge: 164 Bewertung:  (21)

(0)  Dear Expert    Thanks for your valuable reply. I have one doubt in the above thread. where i should enable the router? either in PG/PC or SIMOTION ? should i give any IP address to my HMI? I have attached my ethernet settings with hardware configuration in word format. Please let me know where i should change the settings to access the HMI from my PG/PC. PG/PC IP : 169.254.52.198 SIMOTION IP: 169.254.52.197 and MPI/DP address of HMI is: 21. I am using cross ethernet cable to connect simotion DP/MPI port and HMI. thank you Dateianhang: detail_hardware_config.zip  (10 Downloads) === Edited by Mothilal @ 12/5/2011 7:28 AM [GMT ] === === Edited by Mothilal @ 12/2/2011 11:37 AM [GMT ] === ***ALL IS WELL***

Top

  05.12.2011, 07:26

Mothilal Beigetreten am: 30.11.2011 Letzter Besuch: 12.03.2013 Beiträge: 164 Bewertung:  (21)

(0)  Dear all        In Wincc flexible 2008 "help" file, Routing via Simotion cpu : The transfer of the configuration via S7 Ethernet does not work in case of routing via SIMOTION CPU 4.1.2      my simotion version is : V4.1        The above statement is suited to my project? i have tried so many times but i could not make the connection between PG/PC to HMI. is it(cpu version) a reason for my problem? please let me know Thanks ***ALL IS WELL***

Top