SIMODRIVE Converter system

Error measurement circuit of absolute corrent

Thread Starter: Timóteo   Started: 12/15/2008 3:50 PM   Replies: 15

  12/15/2008, 3:50 PM

Timóteo Joined 11/18/2008 Last visit: 1/21/2009 Posts: 18 Rating:  (0)	(0)  Hello all, I have a simodrive 611-A with now dispaly to me this error 300501 Axis C1 drive 5 error measurement circuit of absolute corrent. Some one was changing thinks in the machine and know i have the error... Is the drive fault, can be a software problem or switch configuration? Does anyone know what to do? Thanks Tim
	Top

  12/15/2008, 4:10 PM

Gebhardt Karl Joined 7/16/2006 Last visit: 5/20/2013 Posts: 1446 Rating:  (164)	(0)  Select Error  300501  in Display   then push the "HELP"-Button. Here you can read aditional help-Informations. (MMC103 and PCU50) Karl
	Top

  12/15/2008, 4:15 PM

Gebhardt Karl Joined 7/16/2006 Last visit: 5/20/2013 Posts: 1446 Rating:  (164)	(0)  What HMI do you have  ? MMC103 ? PCU50   ? Do you have OLD Parameters from your Maschine  ? Karl
	Top

  12/15/2008, 4:19 PM

Timóteo Joined 11/18/2008 Last visit: 1/21/2009 Posts: 18 Rating:  (0)	(0)  Hello 300501 Axis C1 drive 5 error measurement circuit of absolute corrent. But i know the error the problem is that i dont know if it is a software or a hardware error... This hapen when i trie to turn the spindle motor manually on. Thanks Tim
	Top

  12/15/2008, 4:37 PM

Gebhardt Karl Joined 7/16/2006 Last visit: 5/20/2013 Posts: 1446 Rating:  (164)

(0)  >300501 Axis C1 drive 5 error measurement circuit of absolute corrent. You have an 611D   NOT 611A  ! ? >But i know the error the problem is that i dont know if it is a software or a hardware error... Do you have the same power-unit. Then you can twoogle both modules. Do you have you change Paramers  ? >This hapen when i trie to turn the spindle motor manually on Tell me, how you can make this ??? Tell me the Siemens - Number from Power-Unit and controllercard. Karl

Top

  12/15/2008, 4:52 PM

Timóteo Joined 11/18/2008 Last visit: 1/21/2009 Posts: 18 Rating:  (0)	(0)  driver: 6SN1123-1AA00-0FA0 Control board: 6SN1118-0DG22-0AA0 NCU 572: 6FC5252-0AX21-0AB0 And an old MMC103: 6FC5253-0AB07-0AA0 Thanks Tim
	Top

  12/15/2008, 5:29 PM

Gebhardt Karl Joined 7/16/2006 Last visit: 5/20/2013 Posts: 1446 Rating:  (164)	(0)  >MMC103 O.K. Can you save actual NCK-Data in Archive After save NCK-Data you can load an old NCK-Data from Archive. For Information: If you change NCK-Mada  -->  the old and Working NCK-Datas are loaded. Work the Maschine now ? Karl
	Top

  12/15/2008, 5:36 PM

Timóteo Joined 11/18/2008 Last visit: 1/21/2009 Posts: 18 Rating:  (0)	(0)  Hello, I have a ghost of the drive of the MMC103... To make a copy of the NCU what software do i need? The machine is give me the same error... i think the drive is broken! Do you have the schematic/ service manual to fixe it? Thanks Tim
	Top

  12/15/2008, 5:50 PM

Gebhardt Karl Joined 7/16/2006 Last visit: 5/20/2013 Posts: 1446 Rating:  (164)

(0)  >I have a ghost of the drive of the MMC103... O.K. But you need it only, when the Harddisk is defekt. >To make a copy of the NCU what software do i need? There is on the MMC. Do you have the Password of manufactor. Set the manufactor - password. Go to "Dienste" (German-Language) Make IBN-Service >The machine is give me the same error... i think the drive is broken! >Do you have the schematic/ service manual to fixe it? Do you have DocOnCD   ? Karl

Top

  12/15/2008, 6:03 PM

Timóteo Joined 11/18/2008 Last visit: 1/21/2009 Posts: 18 Rating:  (0)	(0)  hello, I have the disc of the mmc here conected to the pc with a usb adaptor, and now what to do? I don't have the manufacter password... Dont have the DocOnCD to.. Thanks for your time! Tim === Edited by Timóteo @ 12/16/2008 9:10 AM [GMT ] ===
	Top