Print document

Technical Forum

LOGO!

Counter completed

Thread Starter: Zazu   Started: 7/1/2012 7:42 AM   Replies: 2

« Previous thread Next thread »
Page 1 of 1 (3 items)
  7/1/2012, 7:42 AM
Zazu
Joined 3/4/2011
Last visit: 5/18/2013
Posts: 25
Rating:
Rated: no ratings [0 out of 5 / rated 0 time(s)]. (0) 
Rated: no ratings [0 out of 5 / rated 0 time(s)]. (0) 
I have put a few posts on here regarding a meterage counter for an extrusion line and received some great help and advice. Well guess what, I actually got it working. It might not be very elegant or efficient as far as programming goes but it does work.
I would be more than happy to upload the program (0BA7), if anyone is interested in taking a look. I would welcome any advice or criticism.
One other thing, is it possible to directly address each block on a LOGO TD.
Thank you to everyone who's taken the time to chip in with advice so far. I wouldn't have been able to do it without you. grin
Top
  7/1/2012, 1:29 PM
desmul24
Joined 6/19/2010
Last visit: 4/27/2013
Posts: 174
Rating:
Rated: Outstanding [3.95 out of 5 / rated 22 time(s)]. (22) 
Rated: no ratings [0 out of 5 / rated 0 time(s)]. (0) 
Zazu wrote:
I have put a few posts on here regarding a meterage counter for an extrusion line and received some great help and advice. Well guess what, I actually got it working. It might not be very elegant or efficient as far as programming goes but it does work.
I would be more than happy to upload the program (0BA7), if anyone is interested in taking a look. I would welcome any advice or criticism.
One other thing, is it possible to directly address each block on a LOGO TD.
Thank you to everyone who's taken the time to chip in with advice so far. I wouldn't have been able to do it without you. grin


Dear Zazu ,
Congrats for your success !!! and Thank you for thanking experts !!!
Some of the members (including me) runs away after they got solution from this forum. I think it is good practice for the development of this forum to let know the result of the solution forwarded by forum members and experts.

Thanks again Rnf:lblSmileyTooltip_
You like it? Rate it !


ለማንኛውም የፋብሪካ አውቶሜሽ ስራ፣ በተለይም፡

ፒ. ኤል.ሲ፣ድራይቭ፣ኮምፒዩተራይዝድ ማሽን ስራ፡በዚህ ይደውሉ 0922 493737
Top
  7/1/2012, 2:09 PM
Zazu
Joined 3/4/2011
Last visit: 5/18/2013
Posts: 25
Rating:
Rated: no ratings [0 out of 5 / rated 0 time(s)]. (0) 
Rated: no ratings [0 out of 5 / rated 0 time(s)]. (0) 
OK I've decide to upload the program and see if any of our experts can suggest ways to improve it.
Just a couple of notes. The four function keys are used to set the preset meterage and I5 is the count input. I7 must be made for a reel change and reset to take place and I1 starts the winder which has to be on for the counter to function.
I5 is set as frequency and maximum is 4100 which equates to 123 M/min.

Enjoy.

Attachment: ReifCounter80.zip  (34 Downloads)
Top
Page 1 of 1 (3 items)
Actions
Copy Link
To conference